ASR NCS 907 100GE 40GE 10GE GE Router Brzegowy Pełna Redundancja
Zasilanie AC, Dostępne Interfejsy: 100GE QSFP28 SR LR ER4L 10GE SFP+ GE SFP
Dual RSP3 480Gbps Dual AC
100% wydajność ( Throughput ) brak potrzeby licencjonowania/rozszerzania.
Zdjęcia poglądowe. Mam ich więcej.
Router spełnia najnowsze standardy.
Soft 17.09 / 17.13 IOS XE
Urządzenie jest w pełni wspierane przez producenta. Nie dotyczy end of life and of seals czy Supportu.
A jako wisienka na torcie, umiarkowane spalanie ;)
(Proszę o podawanie jakim obsadzeniem kart / portów jesteście zainteresowani.)
Uwaga, proszę nie mylić z routerami serii ASR 1000 z 1001x 1002x i podobnymi. Wydajnościowo kierunek A9K / A99xx

Swapping of Interface Modules
The following Ethernet interface modules support swapping on the Cisco A900-RSP3C-400-W module.

8-port Gigabit Ethernet SFP Interface Module (8X1GE)

8-port Gigabit Ethernet RJ45 (Copper) Interface Module (8X1GE)

SFP Combo IM—8-port Gigabit Ethernet (8X1GE) + 1-port 10 Gigabit Ethernet (1X10GE)

Copper Combo IM—8-port Gigabit Ethernet (8X1GE) + 1-port 10 Gigabit Ethernet Interface Module(1X10GE)

2-port 10 Gigabit Ethernet Interface Module (2X10GE)

2-port 40 Gigabit Ethernet Interface Module (2X40GE)

1-port 100 Gigabit Ethernet Interface Module (1X100GE)

2-port 100 Gigabit Ethernet (QSFP) Interface Module (2X100GE)

1-Port OC-192 or 8-Port Low Rate CEM Interface Module

48 T1/E1 TDM Interface Module (48XT1/E1)

48 T3/E3 TDM Interface Module (48XT3/E3)

Cisco ASR 907 Router Features
The key feature of the Cisco ASR 907 Router is to increase per platform and rack-unit interface density, especially when combining multiple interface types such as Gigabit Ethernet (GE), TDM, 10GE, 40GE, and 100GE.

The Cisco ASR 907 Router has the following hardware features:

A larger service scale and higher throughput (400G) Route Switch Processors (RSP)—A900-RSP3C-400-W

One-port 100GE Interface Module (A900-IMA1C)

Two-port 100GE QSFP28 Interface Module (N560-IMA2C)

Note
After SSO, the packet rate increases and the packet count may vary.
Two-port 40GE Interface Module (A900-IMA2F)

1200-Watt PSUs to power the new RSP modules.

The Cisco ASR 907 Router includes the following specific components:

Larger chassis—7 rack units in height while still maintaining a shallow depth and side-to-side airflow.

Larger fan-tray with removable dust filter.

New form factor and higher performance RSP—This high performance RSP has aggregate switching capacity of 480 Gbps in oversubscribed mode.

The backplane and the RSP together have the provision to support higher density 10GE modules like 8x10GE and 100GE modules.

Airflow baffle to allow a system to redirect air and allow front-to-back airflow for cooling.

Flexible I/O configurations through 16 hot pluggable interface modules (single width). For example, with RSP3-400-W in oversubscribed mode:

16x10G + 2x100G + 80x1G

48x10G

Metro ENET switching features along with TDM pseudowire support.

Network processor provides flexibility to off-load control plane CPU processing for select OAM and management packets (for example, CCM, BFD, LBM).

Flexible ENET processing through table-driven packet processing engines.

On-line insertion or removal (OIR) of all FRUs except GPS module, while the system is operational.

Power supply (1+1)—Support for both, AC and DC power supplies. A single power supply can support full system load. If there are two PSUs in the system, they work in a load-sharing mode.

Fully redundant system with redundant combined control plane and data plane (excluding interfaces), timing support, power supplies, and fans.

Active and standby support of redundant control plane and data plane, and timing

Intrachassis IOS redundancy (requires both RSPs).

Stateful-switchover (50 ms) between active and standby RSPs (for protocols that are supported by IOS).

In-service software upgrade (ISSU) supported with same RSPs.

Timing support for receipt and distribution of network frequency and time including SyncE, BITS, 1PPS/10MHz I/O, IEEE 1588-2008, and NTP.

Support for ENET OAM.

T1/E1 line protection compliant with NEBS GR-1089.

Metro Services Metro IP Services Metro Aggregation Services
QoS, with deep buffers and hierarchical IP routing (RIP, OSPF, EIGRP, BGP, IS-IS) MPLS (LDP and VPN)
QoS (HQOS)
Layer 2: 802.1d, 802.1q PIM (SM, DM, SSM), SSM mapping MPLS TE and FRR
Ethernet Virtual Circuit (EVC) BFD MPLS OAM
Multi-VRF CE (VRF lite) with service MPLS-TP
awareness (ARP, ping, SNMP, syslog,
trace-route, FTP, TFTP)
Ethernet OAM (802.1ag, 802.3ah)
Pseudowire emulation (EoMPLS,
CESoPSN, and SAToP)
IEEE 1588-2008 Ordinary Slave Clock and
Transparent Clock
Multiple Spanning Tree (MST) and
Resilient Ethernet Protocol (REP)
Synchronous Ethernet — VPLS and HVPLS
IPv4 and IPv6 host connectivity — Pseudowire redundancy
— — MR-APS and mLACP